822 90 11-51
Safety information
Before installing and first using the dishwasher, read this instruction booklet carefully, including its
hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all
people using the dishwasher are thoroughly familiar with its operation and safety features.
Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so
that everyone using it through its life can be properly informed on appliance use and safety.
● If you take any dishes out of the dishwasher before the
Installation and servicing
end of the dishwashing cycle, it is extremely important
to rinse them thoroughly under running water to remove
any remaining detergent.
● All installation and service work done on the product
must be carried out by a qualified technician. Work
performed by persons with inadequate knowledge may
adversely affect the satisfactory functioning of the
product and may cause personal injury or damage.
Before any work is carried out on the dishwasher, it
must be isolated from the electrical supply. To do this
the power plug must be removed from the wall socket.
● The water safety system protects against water damages.
The following requirements must be fulfilled:
- The dishwasher must be electrically connected when
it is shut off.
- The dishwasher must be correctly installed.
- Always shut off the water supply whenever the dish-
washer is left unattended for an extended period.
● Water connection shall be made via an easily accessible
stopcock.
● In the event of flooding or leakage, shut off the water
supply immediately by closing the stopcock and dis-
connect the power supply by unplugging the power cord
or removing the fuse. When removing the electrical
plug, grip the plug, not the lead.
● The power cable must be plugged into an earthed
socket, which need to be easily accessible. Permanent
installation must only be carried out by an authorized
electrician.
● Make sure that the power cable is not nipped or other-
wise damaged and that the hoses do not get crushed
or kinked when moving the dishwasher in connection
with installation or cleaning etc.
Conservation
- packaging:
● Servicing and possible repairs must be carried out by
a service company authorized by the supplier. Use only
spare parts supplied by these. Never try to repair the
dishwasher yourself.
All materials used in packaging this appliance are environ-
mentally-friendly. The various plastics used are identified
and can be recycled.
- old apparatus:
At the end of the appliance's useful life, disconnect the
electrical plug from the power supply, then cut the electrical
cable at the point where it enters the appliance. Make quite
sure that children will not be able to play with it.
Child Safety
● The dishwasher should be used by adults only. Do not
let children play with the controls or other parts of it.
● Remember that the plastic bags included in the
packaging can be fatal playthings for small children.
● Keep all detergents in safe place out of children´s
reach.
● Prevent children from sitting, swinging or standing
on the open door.
During Use
● This dishwasher is designed solely for washing house-
hold utensils suitable for machine washing. Using it for
other purposes could lead to physical injury or damage
to property and invalidate the guarantee.
● Avoid opening the door while the dishwasher is running,
as hot steam may escape.
● Only use detergent specifically designed for use in
dishwashers.
● Do not place sharp knives with their points upwards.
It is much safer to lay them horizontally in the basket.
822 90 11-51
- 3 -
Description of the appliance
4
5
- 4 -
Zanussi recommends the use of Finish dish-
washer detergent and Rinse Aid.
Spray arm (1)
It is important to keep all the holes in the spray arm clear.
A clogged hole can seriously affect washing efficiency.
If the spray arm needs cleaning, unscrew the nut anti-
clockwise, remove the washer and lift off the spray arm.
Clear the holes and shake out any food remnants.
Water softener (6)
This dishwasher is equipped with a water softener for hard
water. The lime in hard water causes white deposits to
occur on dishes and to the interior of the dishwasher.
To prevent this, the water has to pass through a special
container where the hardness is removed.
Coarse strainer/microfilter (2)
The purpose of the coarse strainer is to catch large objects
such as toothpicks and pieces of eggshell. Make sure
that the strainer is always clean. Turn the coarse strainer
anti-clockwise. Lift it out and rinse it under running water
whenever necessary.
Since the water softener uses coarse dishwasher salt,
you will have to refill the salt container after a certain
number of dishwasher cycles.
It is extremely important, that the salt container
is filled up with the coarse dishwasher salt before
using the dishwasher for the first time.
Fine filter (3)
It is just as important to keep this filter clean. A dirty or
clogged filter will always impair washing efficiency.
The fine filter can easily be lifted out for cleaning when
you have removed the coarse strainer.
The
indicator light on the control panel is lit when the
container requires refilling.
1. Unscrew the filler cap to the salt container anti-
clockwise.
2. Fill the salt container with water (only the first
time).
Detergent dispenser (4)
Open the lid to the dispenser by pressing the lid catch
towards the compartment. Consult the instructions on the
detergent packet, fill the compartment accordingly and
close the lid. Pre-wash detergent is poured into the smaller
compartment to the left when needed. This detergent is
active allready at pre-rinsing. Make sure that there is no
items that prevents the lid from opening.
3. Fill the container with dishwasher salt, using the
funnel supplied.
4. Remove the funnel and wipe off any spillage
around the filler opening.
5. Screw the filler cap back properly in place.
Only use detergents specially designed for dish-
washers.
The water softener is now ready for the first load of dishes.
Always make sure that there is coarse dishwasher salt in
the container, which holds about 1 litre.
To adjust the water softener, see page 7.
Rinse aid dispenser (5)
Use of rinse aid will result in cleaner and faster drying of
the load, since it helps water and soil to run off.
Too much rinse aid may result in streakiness, too little
may cause white spots. The dispenser holds about 150 ml.
This is enough for approx. 60 wash cycles, depending
on the dosage setting. Adjust the dosage setting according
to the hardness of the water.
Only use special salt for dishwashing machines,
ordinary domestic salt, especially table salt, can
damage the water softener.
You can set the dosage between 1 - 6, the appli-
ance is factory set to 1.
Begin at the lowest dosage setting and increase
if necessary by turning the setting arrow with e.g.
the handle of a spoon.
The
indicator light on the control panel is lit when the
dispenser requires refilling.
1. Open the lid to the dispenser by pressing the lid
catch towards the compartment and lift the lid.
2. Fill up with rinse aid; do not overfill.
3. Wipe off any spillage carefully to prevent excessive
foaming during the next wash programme.
4. Close the lid and press until it locks again.
Do not fill the rinse aid dispenser with liquid
detergent.
- 5 -
The control panel
Indicator and
control lamps
Indicator lamps
delayed start
On/Off button
Control lamp
Water softener
button
Delay start
button
Functions
button
Programme
buttons
Water softener and functions button:
In addition to selecting a programme you can press these
two buttons to adjust the setting of the water softener.
Control lamps:
Shows that • On/Off button is pushed in
Indicator lamps:
Shows • Current phase of the selected programme.
• Refilling of salt container is necessary
• Wash cycle in progress
• Drying in progress
top lamp
middle lamp
lowest lamp
• Refilling of the rinse aid dispenser
is necessary
• Programme cycle
ended
How to set the delayed start
The programme start can be delayed by 3, 6 or 9 hours.
Reset the delayed start:
If the programme has not started, you can change
the set time with the delayed start button.
1. Press in the On/Off button.
2. Press the delay start button repeatedly, until the
lamp next to the required hours of delay is lit.
Cancelling the delayed start:
If the programme has not started, the delayed start
can be cancelled. Press the delay start button repeat-
edly, until none of the lamps next to the hours are lit.
The required programme starts immediately.
3. Press the button for the required programme.
4. After the set delayed start time has elapsed,
the programme starts.
- 6 -
Adjusting the water softener
To prevent limescaling on the dishes and to the interior of the
dishwasher, the dishes must be washed with soft water.
Contact your local Water Authority to find the
exact water hardness level for your area.
This dishwasher is equipped with a water softener, where tap-
water which is harder then 4 °d (german degree) is softened.
The water softener has 5 settings:
Adjust the water softener according to the table below for the
water hardness level for your area.
Setting on the
Number of
Water hardness level
water softener
light flashes
1)
2)
i °d
i mmol/l
> 24
18 - 24
12 - 18
4 - 12
4,2
5
5
4
3
2
1
3,2 - 4,2
2,1 - 3,2
0,7 - 2,1
below 0,7
4
3
2*
below 4
1
no salt is needed
In both of the following settings the dishwasher must be switched off and all programmes completed.
See page 9 for the programme cycles.
1. Press the water softener and functions buttons
simultaneously and hold them pressed in, then
also press in the On/Off button.
If dishwasher detergent with rinse aid is used,
you can switch off the lamp that indicates that
the rinse aid dispenser is empty.
2. When the lamps for the water softener and
functions buttons starts to flash, you can let go
of the buttons.
1. Press the water softener and functions buttons
simultaneously and hold them pressed in, then
also press in the On/Off button.
3. Press the water softener button once. At first the
lamp will be solid, then it starts to flash.
2. When the lamps for the water softener and
functions buttons starts to flash, you can let go
of the buttons.
- The number of flashes are equivalent with the
set water hardness level.
3. Press the functions button once. The lamps for
the functions button and ended programme cycle
starts to flash. Press the button once more and
the light for the ended programme cycle goes out.
Now the function for the rinse aid control light
is off.
- This sequence of flashes is repeated several
times after a few seconds pause.
4. The water hardness level is raised by 1 step
every time you press the water softener button.
After hardness level 5 comes hardness level 1.
4. Press out the On/Off button to complete the setting.
5. Press the On/Off button when the required water
hardness level is selected. This saves the selection.
To reset the function, follow steps 1 and 2 above
and then press the functions button twice, until
the lights for the functions button and for ended
programme cycle begin to flash again.
If the setting 1 is chosen, the salt indicator lamp
is not lit.
1) german degree of measurement for the water
hardness
2) millimol, internationel unit for water hardness
*) factory setting
- 7 -
Programme chart
All types of
dishes
Coffee cups,
delicate items
Plates and
cooking pots
Type of
dishes
• heavily
soiled
Type of
soil:
• normaly
soiled
• normaly
soiled
• lightly
soiled
• lightly
soiled
• dried-on food
remnants
• dried-on food
remnants
especially egg-
white and starch
Suitable
programme:
INTENSIVE
70° C
GLASS
40° C
NORMAL
65° C
ENERGY SAVE
QUICK
50° C
3)
55° C
Pre-wash
Washing
2 x rinses
Final rinse
Drying
Programme
Pre-wash
Washing
Rinse
Final rinse
Drying
Pre-wash
Washing
Rinse
Final rinse
Drying
-
-
1)
Washing
Rinse
Final rinse
-
Washing
Rinse
Final rinse
-
cycle:
Consumption
2)
figures:
Washing
time with
drying:
112 minutes
92 minutes
150 minutes
35 minutes
30 minutes
Drying time:
Energy:
12 minutes
1,15 kWh
9 litres
12 minutes
0,80 kWh
7 litres
50 minutes
0,63 kWh
7 litres
—
—
0,40 kWh
6 litres
0,35 kWh
6 litres
Water:
1) Different parts of the wash programme may not sound the same, because the wash action is more intensive
at some stages.
2) Consumption figures have been calculated for nominal conditions. The figures can vary depending on inlet
water temperature and how full the main and cutlery basket are.
3) Consumption figures and performance is according to the Energy Save programme cycle.
All programme cycles begins with a drainage.
Dishwashing detergent in tablet form is not suitable
for use in the Quick- and Glass programme cycles.
- 8 -
Using the appliance
Starting the programme
Pause function
1. Scrape or rinse off solid food remnants.
With the pause function the programme can be temporarily
disrupted for a short period of time.
2. Load the dishwasher.
(See the basket and loading in page 10).
1. Press in the On/Off button. The programme stops.
2. All lamps goes out.
3. Put the correct amount of detergent into the
detergent dispenser and close the dispenser lid.
3. When you want the programme to continue again,
you press the On/Off button.
4. Close the door.
The programme continues.
5. Press in the On/Off button.
The programme should not be paused for any
longer than necessary, because the water inside
the dishwasher has cooled down and must be
heated again which increases the power
consumption.
6. Press in the required programme button (see pro-
gramme chart). Programme indicator lamp is lit.
During the six seconds the two top indicator lamps
are flashing, you can select another programme
cycle. If not, the selected programme starts.
The lamp indicates which part of the selected
cycle the dishwasher is in.
Cancelling the drying phase
In case you do not want to wait until the drying phase is
completed, you can cancel it.
7. Check the strainers/filters to see if they need to
be cleaned when the dishwasher has finished
the programme.
1. Press in the On/Off button. The control lamp for
the On/Off button goes out.
If both the top and middle indicator lights are
flashing, first check that the door is properly closed,
if it is read the section ”Something Not Working”.
2. Open the door. The drying phase is cancelled.
Switching the dishwasher off
Stopping the programme temporarily
Do not switch the dishwasher off until the indicator lamp
for the programme cycle end is lit.
1. Open the door. The programme stops.
1. Press in the On/Off button. The control lamp for
the On/Off button goes out.
2. Top or middle indicator lamp is flashing depending
on how far the programme cycle has gone.
Be careful if you open the door immediately
after the programme is finished, since hot steam
may escape.
3. Close the door and the programme continues
after about 6 seconds.
Open the door carefully when the dishwasher is
running, since hot steam may escape.
This dishwasher has a new feature called
”IMPULSE WASHING”. This washing system
varies both the revolutions of the pump and the
water pressure for more intensive cleaning of the
dishes during a programme. That is why different
sections of the programme cycle do not sounds
the same.
Cancelling the programme
1. Press and hold in the button for the programme
in progress until the indicator light for the pro-
gramme goes out.
2. Release the programme button. The programme
is now cancelled and a new programme can be
selected.
If you switch the dishwasher off, the selected
programme is not finished, it is only paused.
When you start the dishwasher again, the pro-
gramme will continue.
- 9 -
Loading and unloading the dishwasher
How to load the dishes
Baskets
The illustration shows the dishwasher loaded with six
place settings. Your own dishes are not likely to be
identical to this load, but if you follow the advice below
we are sure you will be pleased with the results.
Main basket
Cutlery basket
● Always place glasses, cups and bowls upside down.
● Incline deep dishes (soup plates etc.) so that the
water can run off when drying.
● Make sure that the dishes do not rest against each
other. This is particularly important in regard to the
cutlery basket - nested spoons, etc. simply cannot be
properly washed. The water must get at all the soiled
surfaces.
● Make sure that cutlery with slender handles and other
items do not protrude through the openings in the
basket and prevent the spray arm from rotating.
● Never put silver and stainless steel objects together.
When these metals come into contact with each other
a chemical reaction occurs which stains the silver.
● China with a pattern applied on top of the glaze may
not be suitable for machine washing as the colours
may fade and lose their lustre. The same applies to
cutlery with wooden or plastic handles.
Make sure you always buy articles that are
dishwasher proof.
● Silver and aluminum items tend to be discolour when
washed. Food remnants from egg and mustard often
causes discolourations and stains on silver. Make sure
to rinse off and remove food remnants on silver if it is
not washed immediately after it has been used.
● Not all plastic articles are machine washable. If you
are in doubt as to whether your plasticware can be
machine washed, we suggest you check by washing
a single item or else wash them by hand.
● When washing delicate items, select the programme
with the lower wash temperature.
● Substances such as ketchup containing strong colouring
agents can cause temporary discolouration to the
interior of the dishwasher.
Do not place sharp knives with their points up-
wards. It is much safer to lay them horizontally
in the main basket.
If required, the top and the handle to the cutlery
basket are removable.
Unloading
Hot dishes are sensitive to mechanical shocks. Always let
the dishes cool down before unloading.
The dishes dry faster if the door is opened
slightly for a short time once the programme
has finished.
- 10 -
Maintenance and cleaning
General cleaning
Moving the dishwasher
Inspect the filters and spray arm nozzle before re-loading If you have to move the dishwasher (you are moving
the dishwasher and remove any food scraps. Wipe round house, etc):
the rubber gasket at the bottom of the door to remove
grease which tends to collect there.
1. Unplug it.
2. Turn off the water tap.
Cleaning the filters
3. Remove the water inlet and discharge hoses.
There are two filters, a coarse one and a fine one which
should be cleaned after every wash. Lift out these filters
which are in the base of the dishwasher and wash under
Avoid tilting the dishwasher during transportation.
Protecting the dishwasher against
running water.
freezing
The dishwasher must not be used without the
If the dishwasher is placed in an environment
filters. Incorrect repositioning of the filters will
produce poor washing results.
where the temperature sometimes fall below 0° C,
there is a risk that the small amount of water which
remains inside the parts of the dishwasher will
freeze and damage it. To prevent this you should:
Cleaning of the filters is vital to ensure correct
operation of the dishwasher.
1. Turn off the water supply to the dishwasher.
2. Remove the water inlet and discharge hoses.
Cleaning the spray arm nozzle
The holes in the spray arm nozzle must be kept free of
scraps for the efficiency of the washing action.
Inspect the spray arm regularly. When thorough cleaning
is necessary, remove the spray arm by unscrewing the
nut anti-clockwise, remove the washer and lift off the
spray arm.
3. Make sure that there is dishwasher salt in the
salt container for the water softener.
The appliance is only to be used and stored
indoors at normal room temperature. The manu-
facture is not responsible for any frost damage.
Wash the spray arm with hot soapy water using a stiff
saucepan brush if necessary to remove scraps.
Re-assemble carefully, making sure the nut is secure.
Cleaning the cabinet
Wipe the outside of the cabinet and control panel regularly
with a soft damp cloth. When necessary, use washing up
liquid to remove stubborn marks, rinse with a damp cloth
and rub up with a soft duster.
Never use abrasive cleaners which could damage the
surface, ie: scouring pads or solvents (acetone, trichlori-
ethylene, etc).
If the dishwasher is not going to be used for some time,
take the following precautions:
1. Unplug the dishwasher and turn off the water
supply.
2. Fill up the rinse aid container.
3. Make sure the tub is clean by carrying out a
wash programme (without any crockery) using
Finish Dishwasher cleaner, then dry the inside
thoroughly.
4. Leave the door ajar.
- 11 -
Something Not Working
Before calling out an engineer, please check through the details below because some faults can be rectified easily
without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a
fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee.
Fault
Check
• Is the door closed properly?
The programme will not start.
• Have you pressed the On/Off button?
• Is the water tap turned on?
• Is the dishwasher plugged in?
• Has the fuse blown? (Start with fuse in electrical plug).
• Is the delay start-button pressed in?
• Is the previous programme finished? (See page 9).
• Is the water tap turned on?
The dishwasher is not filling with water.
• Has your domestic water supply been cut off temporarily?
• Is the water inlet hose kinked or blocked?
• Is the filter inside the inlet hose blocked?
• Is the water pressure too low?
• Did you open the door before the indicator light
is lit and the programme cycle finished?
• Is the previous programme finished? (See page 9).
• Are the filters clogged?
Water not discharged at end of cycle.
Dishes not washed satisfactorily.
• Has anything prevented the spray arm from rotating?
• Are the spray arm holes clogged?
• Were the dishes packed too close together?
• Are the filters clogged?
• Are the filters fitted correctly in place?
• Did you use enough detergent?
• Is the salt container cap properly closed?
• Did you select a programme with too low temperature?
• Is the rinse aid dispenser empty?
Visible lime deposits or white film
on the dishes.
• Is the salt container empty or is the water softener not
correctly adjusted?
• Is the rinse aid dispenser adjusted to too low dosage?
The dishwasher is noisy.
• Are the dishes rattling against each other?
• Is the spray arm knocking against the dishes?
Whistling sound when washing.
• This is not a fault, try another brand of detergent.
The dishes are not quite dry and are
not shiny.
• Is the rinse aid dispenser empty?
• Have the dishes been left too long inside the dishwasher?
The door is difficult to close.
• Is the dishwasher level?
If the top or middle indicator lamp is flashing, it is possible that you can solve the problem yourself. When the problem is
solved, press in the On/Off button and the programme continues. If the problem occurs again, contact your local
Service Force Centre. If any other lamps flash contact and inform your local Service Force Centre.
Fault
Check
• Is the water tap turned on?
The top indicator lamp flashes.
• Is the filter inside the inlet hose blocked?
• Is the water inlet hose kinked or blocked?
• Is your domestic sewer system blocked?
The middle indicator lamp flashes.
- 12 -
Service
Service and Spare Parts
Customer Care Department
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:
For general enquiries concerning your Zanussi appliance
or for further information on Zanussi products, please
contact our Customer Care Department by letter or
telephone at the address below or visit our website at
08705 929929
Customer Care Department
Zanussi
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
55-77 High Street
Slough
Berkshire
For the address of your local Service Force Centre and
further information about Service Force, please visit the
SL1 1DZ
Tel:
Before calling out an engineer, please ensure you have
read the details under the heading ”In the event of a fault”.
08705 727727 *
* call to this number may be recorded for training purposes.
When you contact the Service Force Centre you will need
to give the following details:
1.
2.
3.
4.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance
(found on the rating plate)
5.
The purchase date
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
Never attempt to repair the dishwasher yourself.
Repairs carried out by unauthorized or inexperienced
persons can cause injury or serious malfunctioning.
Information for test centres
The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual.
Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using
detergent and a clean load.
Test standard:
EN 50242 och EN 60704
Rated capacity:
6 place settings accordance EN 50242
accordance figure on page 10
energy saving 55° C
Loading of basket:
Test program:
Detergent (IEC type B):
Rinse aid (type III):
Feed water pressure:
15 gram in the dispenser + 3 gram in the pre-wash dispenser
setting 3
minimum 0,8 bar, maximum 10 bar
- 13 -
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof
is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the
same FREE OF CHARGE for labour, materials or carriage on condition that:
•
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions
•
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us
•
•
•
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre
Any appliance or defective part replaced shall become the Company’s property
This guarantee is in addition to your statutory and other legal rights
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in
which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom
Appliances found to be in use within a commercial environment, plus those which are the subject to rental
agreements
Products of Zanussi manufacture which are not marketed by Zanussi
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject
to the following qualifications:
•
•
The guarantee starts from the date you first purchased your product
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products
•
•
•
This guarantee relates to you and cannot be transferred to another user
Your new home is within the European Community (EC) or European Free Trade Area
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household
•
The product is installed taking into account regulations in your new country
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and
your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 99
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219897
Nurnberg
Pordenone
Stockholm
Slough
Sweden
UK
- 14 -
Installation instructions
Any electrical work required to install this appliance,
should be carried out by a qualified electrician or
competent person.
Any plumbing work required to install this appliance,
should be carried out by a qualified plumber or
competent person.
Technical specifications
Capacity:
6 place settings accordance EN 50242
Dimensions:
Height
447 mm
546 mm
480 mm
507 mm
Width
Depth (to the edge of the door)
Depth (to the middel of the door)
Weight:
Net
22 kg
Water pressures:
Minimum
Maximum
Maximum
80 kPa (0,8 bar)
1000 kPa (10 bar)
65° C
Water temperature:
Electrical data:
Power supply
Fuse
230 V - 50 Hz
13 A
Heating element
Power rating
1000 W
1080 W
This appliance complies with the following E.E.C. directives:
73/23/EEC, dated 19.02.1973 – low-voltage directive.
89/336/EEC, dated 03.05.1989 (incl. amendment
–
–
–
92/31/EEC) – directive on electromagnetic compatibility.
- 15 -
Unpacking
Damages
If the dishwasher has been damaged during transport,
you should immediately notify the company responsible
for delivering it.
Check that the dishwasher is undamaged. If you discover
any damage, faults or that anything is missing, you should
notify the dealer immediately.
Never leave packaging material in a place where
children may play with it.
Check that the following accessories are supplied with the
dishwasher when you unpack it:
1
– A funnel for filling salt (1)
– Elbow for discharge hose (2)
– Washer/filter for inlet hose (3)
2
3
Use
This dishwasher is designed solely for washing household
utensils suitable for washing in a dishwasher. Using it for
other purposes may damage it and invalidate the guarantee.
Identification of materials
All materials used in packaging this appliance are
environmentally-friendly. The various plastics used
are identified and can be recycled:
● PE stands for polyethylene, which is used for the
bag around the appliance and the bag in which these
instructions were supplied.
● PS stands for polystyrene (moulded), which is used
for the sections of packaging needed to cushion the
appliance.
The cardboard components of the packaging are made
from recyclable paper and should be taken to a collection
point for recycling.
The appliance contains plastic and rubber components.
These have identifying marks to show what they are made
from, so they can be recycled or disposed of properly at
the end of the appliance's life cycle.
The materials are identified according to international
standards.
- 16 -
Installation
Positioning
The dishwasher is intended to be installed on a kitchen
sink, worktop or built-in. To function properly, make sure
that the appliance is level. Its height can be adjusted with
the adjustable feets (5 mm each). See the illustration for
built-in measurements.
Water inlet
The dishwasher is equipped with safety features
which are to prevent the water from going back
to the fresh water system. These features are ac-
cording to current water technical safety regulations.
The dishwasher should be permanently plumbed into a
separate cold water supply.
The water pressure must be within the limits given in the
technical specifications, as it will not function correctly if
pressure is outside these specifications.
Your local Water Authority will advise you on the average
mains pressure in your area. Where the water is supplied
from a cold water cistern you can work out the pressure
yourself by measuring the vertical distance (or ‘Head’)
between the dishwasher’s inlet hose and the outlet from
the cold water storage cistern; allowing .86 psi for every 2
feet under normal conditions.
We would advise you to have a shut-off valve or stop-
cock in the water supply pipe close to the dishwasher
and accessible for easy use. This should be turned off
when the appliance is not in use. Insert the combination
rubber washer/filter and connect the inlet hose to a tap
with a 3/4" pipe thread.
The inlet hose must not be joined onto any form of exten-
sion hose. If it is too short, the entire hose must be repla-
ced with a longer high-pressure hose, specially designed
for the purpose. The end of the hose, which is connected
to the dishwasher can be turned in any direction. Loosen
the retaining nut, turn the hose, then retighten the nut.
- 17 -
Installation
Water drainage
To protect the dishwasher against water damage
it is equipped with a water safety system. In the
event of a fault the drain-pump starts automatically
and the remaining water inside the dishwasher is
pumped out.
The water safety system also works when the
dishwasher is switched off. However the dish-
washer must be connected electrically.
Place the discharge hose over the sink as illustrated.
It must not at any point be higher up than 75 cm over the
surface which the dishwasher is standing on. If it runs
higher, operation of the dishwasher might be impaired.
It is also important to ensure that the inside diameter of the
hose is not less than 13 mm at any point. If the discharge
hose is too long, it can easily be cut to the right length.
1. Cut the hose to a suitable length, using a
sharp knife.
2. Fit the elbow supplied onto the end of the hose.
- 18 -
Power supply
The dishwasher is supplied with a lead and electrical
plug for connection to a 230 V, 13 A earthed wall
socket. Before any work is carried out on the
dishwasher, it must be isolated from the electric
mains supply, for example by removing the plug
from the wall socket.
Permanent electrical installation must be
carried out by an authorised electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should
this safety measure not be observed.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
GREEN & YELLOW
Remove the fuse from the cut off plug.
13 AMP FUSE
The cut off plug should then be disposed of to prevent
the hazard of shocks in case it should be plugged
into a 13 amp socket in another part of your home.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
BROWN
CORD CLAMP
BLUE
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13 amp BSI362 fuse.
Only ASTA or BSI approved fuses should be used.
- 19 -
© Electrolux Household Appliances Limited 2002
|