Recycled paper
Printed in Canada
P/N 318132200 (9912) Rev. B
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
Save these instructions for future reference.
This guide contains important safety symbols and instructions. Please pay special attention to these symbols and follow all instructions
given. Here is a brief explanation of the use of these symbols.
This symbol will help alert you to situations that may
cause serious bodily harm, death or property damage.
This symbol will help alert you to situations that
may cause bodily injury or property damage.
• Remove all tape and packaging w rap before using the • Do not leave children alone—Children should not be left
cooktop. Destroy the carton and plasticbags after unpacking
the cooktop. Never allow children to play with packaging
material. Do not remove the serial plate attached to the cooktop.
alone or unattended in the area w here an appliance is in use.
They should never be allowed to sit or stand on any part of the
appliance.
• Proper Installation—Be sure your appliance is properly • DO NOT TOUCH SURFACE BURNERS, GRATES, AREAS NEAR
installed and grounded by a qualified technician in
accordance w ith the National Fuel Gas Code ANSI Z223.1
latest edition, and the National Electrical Code ANSI/NFPA
No. 70—latest edition, and local code requirements. Install
and/or adjust only per installation instructions provided in the
literature package for this cooktop.
THESE BURNERS. Surface burners may be hot even though the
flames are not visible. Areas near surface burners may become hot
enough to cause burns. During and after use, do not touch or let
clothing or other flammable materials touch these areas until they
have had sufficient time to cool. Among these areas are the
cooktop and the surfaces facing the cooktop.
Ask your dealer to recommend a qualified technician and an • Wear Proper Apparel—Loose-fitting or hanging garments
authorized repair service. Know how to shut off gas supply at the
meter and disconnect the electrical power to the cooktop at the
circuit breaker or fuse box in case of an emergency.
should never be w orn w hile using the appliance. Do not let
clothing or other flammable materials contact hot surfaces.
Never use your appliance for w arming or
heating the room.
• User Servicing—Do not repair or replace any part of the
appliance unless specifically recommended in the manuals.
All other servicing should be done only by a qualified technician.
This may reduce the risk of personal injury and damage to the
cooktop.
• Do Not Use Water or Flour on Grease Fires—Smother the fire
w ith a pan lid, or use baking soda, a dry chemical or
foam-type extinguisher.
• Never modify or alter the construction of a cooktop by
removing panels, w ire covers, or any other part of the
product.
• When heating fat or grease, w atch it closely. Fat orgrease may
catch fire if allowed to become too hot.
• Use Only Dry Potholders—Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let the
potholders touch the flame or burners. Do not use a towel or other
bulky cloth instead of a potholder.
Stepping or leaning on this cooktop can result
in serious injuries and may also cause damage to the cooktop.
Do not allow children to climb or play around the cooktop.
• Do Not Heat Unopened Food Containers—Buildup of
pressure may cause the container to burst and result in injury.
• Storage on Appliance—Flammable materials should not be
stored on the cooktop, near surface burners. This includes
paper, plastic and cloth items, such as cookbooks, plasticware and
towels, as well as flammable liquids. Do not store explosives, such
as aerosol cans, on the cooktop. Flammable materials may
explode and result in fire or property damage.
• Know w hich knob controls each surface burner. Always turn
the knob to the LITE position when igniting the burners. Visually
check that the burner has lit. Then adjust the flame so it does not
extend beyond the edge of the utensil.
Do not store items of interest to children in
the cabinets above the cooktop.
Use Proper Flame Size—Adjust flame size so it
does not extend beyond the edge of the utensil. The use of
undersized utensils will expose a portion of the burner flame to direct
contact and may result in ignition of clothing. Proper relationship of
utensil to flame will also improve efficiency.
3
IMPORTANT SAFETY INSTRUCTIONS
(continued)
• Utensil Handles Should Be Turned Inw ard and Not Extend • Glazed Cooking Utensils—Only certain types of glass, glass/
Over Adjacent Surface Burners—To reduce the risk of burns,
ignition of flammable materials, and spillage due to unintentional
contact with the utensil, the handle of the utensil should be
positioned so that it is turned inward, and does not extend over
adjacent surface burners.
ceramic, ceramic, earthenware, or other glazed utensils are
suitable for cooktop service without breaking due to the sudden
change in temperature. Check the manufacturer' s
recommendations for cooktop use.
• Do Not Use Decorative Surface Burner Covers. If a burner
isaccidentallyturned on, the decorative coverwillbecome hot and
possibly melt. You will not be able to see that the burner
is on. Burns will occur if the hot covers are touched. Damage
may also be done to the cooktop or burners because the covers
may cause overheating. Air will be blocked from the burner and
cause combustion problems.
• Never Leave Surface Burners Unattended at High Heat
Settings—Boilovers cause smoking and greasy spillovers that
may ignite, or a pan that has boiled dry may melt.
• Protective Liners—Do not use aluminum foil to line surface
burner pans. Only use aluminum foil as recommended in the
Cooking Guide. Any other use of protective liners or aluminum foil
may interfere with heat and air distribution, and combustion.
Damage to the cooktop or personal injury may result.
SAVE THESE INSTRUCTIONS
4
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
Grounding Instructions
(electric ignition models only)
This appliance is equipped with a 3 prong grounding plug for your
protection against shock hazard and should be plugged directly into a properly
grounded receptacle. DO NOT cut or remove the grounding prong from this plug.
Avoid fire hazard or
electrical shock. Do not use an adaptor
plug, an extension cord, or remove
grounding prong from electrical power
cord. Failure to follow this warning can
cause serious injury, fire or death.
For personal safety, this cooktop must be properly grounded. For maximum safety,
the plug must be plugged into a 120V—60 Hz. outlet that is correctly polarized and
properlygrounded.
If a two-prong wall receptacle is the only available outlet, it is the personal
responsibility of the consumer to have it replaced with a properly grounded three-
prong wall receptacle installed by a qualified electrician.
DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD ROUND
GROUNDING PRONG FROM THE POWER CORD PLUG. SEE THE INSTALLATION
INSTRUCTIONS PACKAGED WITH THIS OVEN FOR COMPLETE INSTALLATION
AND GROUNDING INSTRUCTIONS. DO NOT OPERATE THE OVEN USING A
TWO-PRONG ADAPTER OR AN EXTENSION CORD.
Thisappliance can be used with NaturalGasand Propane Gas. It isshipped from the
factory for use with natural gas.
Liquefied Petroleum
(Propane) Gas
Conversion
If you wish to convert your cooktop for use with propane gas, see the information
in the Installation Instructions.
The conversion must be performed by a qualified service technician in accordance
with the manufacturer'sinstructionsand allcodesand requirementsofthe authority
having jurisdiction. Failure to follow instructions could result in serious injury or
propertydamage. The qualified agencyperforming thisworkassumesresponsibility
for the conversion.
Severe shock or damage
to the cooktop mayoccurifthe cooktop is
not installed by a qualified installer.
5
For most cooking, start on the highest control setting and then turn to a lower one
to complete the process. Use the chart below asa guide fordetermining properflame
size for various types of cooking. The size and type of utensil used and the amount
of food being cooked will influence the setting needed for cooking.
Flame Size
Never extend the flame beyond the outer
edge of the utensil. A higher flame simply
wastes heat and energy, and increases
your risk of being burned by the flame.
For deep fat frying, use a thermometer and adjust the surface control knob
accordingly. If the fat is too cool, the food will absorb the fat and be greasy. If the
fat is too hot, the food will brown so quickly that the center will be undercooked. Do
not attempt to deep fat fry too much food at once as the food will neither brown nor
cook properly.
RIGHT
*Flame Size
High Flame
Medium Flame
Low Flame
Type of Cooking
Start most foods; bring water to a boil; pan broiling
Maintain a slow boil; thicken sauces, gravies; steam
Keep foods cooking; poach; stew
* These settings are based on using medium-w eight aluminum pans w ith lids.
Settings may vary w hen using other types of pans.
WRONG
The color of the flame is the key to proper burner adjustment. A good flame is clear,
blue and hardly visible in a well-lighted room. Each cone of flame should be steady
and sharplydefined. Adjust orclean burnerifflame isyellow-orange. To clean burner,
see instructions under General Cleaning.
Proper Burner
Adjustments
Each burner lights automatically from an electric ignitor each time a control knob is
turned to the LITE position. Two ignitors (one per set of burners) are supplied.
Setting Surface
Controls
To operate the surface burner:
1. Place cooking utensil on burner.
2. Push in and turn the Surface Controlknob to LITE. Onlythe burneryou are turning
on will ignite.
3. Visually check that the burner has lit.
4. After the burner lights, turn the control knob to the desired flame size. The
control knobs do not have to be set at a particular mark. Use the guides and
adjust the flame as needed. DO NOT cook with the control knob in the LITE
position. (The electronic ignitor will continue to click if left in the LITE position,
causing premature wear.)
In the event of an electrical power outage, the surface burners can be lit manually.
To light a surface burner, hold a lit match to the burner head, then slowly turn the
surface control knob to LITE. Use caution when lighting surface burners manually.
Do not place plastic items such as salt and pepper shakers,
spoon holders or plastic w rappings on top of the range w hen it is in use.
These itemscould melt orignite. Potholders, towelsorwood spoonscould catch fire
if placed too close to a flame.
6
Cleaning Various Parts of Your Range
General Cleaning
Before cleaning any part of the range, be sure all controls are turned OFF and the
range is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE.
REGULAR CLEANINGS WILL REDUCE THE NUMBER OF MAJOR CLEANINGS LATER.
Surfaces
Aluminum (Trim Pieces) &
How to Clean
Use hot, soapy water and a cloth. Dry with a clean cloth.
Vinyl
Glass, Painted and Plastic For general cleaning, use hot, soapy water and a cloth. For more difficult soils and built-up
Body Parts, Control Knobs grease, applya liquid detergent directlyonto the soil. Leave on soilfor30 to 60 minutes. Rinse
and Decorative Trim Pieces
with a damp cloth and dry. DO NOT use abrasive cleaners on any of these materials; they
can scratch.
Control Panel
Before cleaning the control panel, turn all controls to OFF and remove the control knobs. To
remove, pull each knob straight off the shaft. Clean as instructed above. Squeeze excess
water from the cloth before wiping the panel; especially when wiping around the controls.
Excesswaterin oraround the controlsmaycause damage to the appliance. To replace knobs
after cleaning, line up the flat sides of both the knob and the shaft, then push the knob(s)
into place.
Porcelain Enamel
BurnerGrates, Cooktop
Surface, Below Cooktop
Clean burner grates, broiler pan and insert in the dishwasher and dry upon removal. If soils
are not removed, follow the cooktop cleaning instructions below.
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution
of clean water and ammonia. If necessary, cover difficult spots with an ammonia-soaked
paper towel for 30 to 40 minutes. Rinse with clean water and a damp cloth, then scrub with
a soap-filled scouring pad. Rinse and wipe dry with a clean cloth. Remove all cleaners or the
porcelain maybecome damaged during future heating. DO NOTuse sprayoven cleanerson
the cooktop.
Stainless Steel, Chrome Parts, Clean with hot, soapy water and a dishcloth. Rinse with clean water and a cloth. Cover
Drip Pans
stubborn spots with an ammonia-soaked paper towel for 30-40 minutes. Rinse. Cleaners
made especially for stainless steel are recommended. Be sure to rinse the cleaners as bluish
stains may occur during heating and cannot be removed.
Surface Burners
The holes in the burners of your range must be kept clean at all times for proper ignition and
a complete, even flame. Clean the burner holes routinely with a small gauge wire or needle
and especially after bad spillovers which could clog these holes.
To remove and replace burner units per your model, see " To Remove and Replace Burners"
underGeneralCleaning. To clean, soakthe burnersin a 1:1 solution ofammonia and water
for 30 to 40 minutes. For stubborn stains, scrub with soap and water or a mild abrasive
cleanserand a damp cloth. Drythe burnersthoroughlyin a warm oven for30 minutes. Then
replace them, making sure they are properly seated and level. DO NOT wash burner units
in the dishwasher.
7
To Raise and Low er the Top for Cleaning
1. Remove burner grates and spillover bowls. Set aside.
2. Grasp the front of the cooktop and then lift.
General Cleaning
(continued)
3. Lift the top high enough to fully raise the support rods. The Lift-up rods will
support the top in its raised position.
4. Clean underneath using hot, soapy water and a clean cloth; then dry.
5. Lower the top gently after lowering the support rod.
When lowering the top,
grasp the sides with fingertips only. Be
carefulnot to pinch fingers. Also, DO NOT
drop orbend the cooktop when raising or
lowering. Thiscould damage the surface.
To Remove and Replace Burners for Cleaning
Your model will have one of the two burners types shown below. Follow the
instructions that correspond with the burners on your cooktop.
Figure 2
DO NOT turn the
burnerson when the cooktop israised for
cleaning. Be sure that the top iscompletely
lowered and securely in place before
turning on the burners.
Figure 1
To Remove Burners (Figure 1)
1. Remove shipping screws with a Phillips® Head screwdriver. See illustration for
screw locations.
2. Tilt the burner at the end closest to the support bar until the locator tab is
released (front burners tilt right, rear burners tilt left). Move it toward the back
of the cooktop. This will separate it from the gas valve at the front of the
cooktop.
To Remove Burners (Figure 2)
1. Remove shipping screws with a Phillips® Head screwdriver. See illustration for
screw locations.
2. Lift burner pair straight up and out.
To Replace Burners (Figure 1)
1. Slide the burnertube overthe gasvalve at the front ofthe cooktop (front burners
fit over the right valve, rear burners fit over the left valve on each side of the
cooktop).
2. Tilt burnerso that the locating tab willslide into the slot on the support bar. Make
sure burners are properly seated on support bar and are level.
3. Replace shipping screws if desired.
To Replace Burners (Figure 2)
1. Place burnerpairovermounting bracket. Make sure burnersare positioned over
gas valves and are properly positioned and level.
2. Replace shipping screws if desired.
8
Before you call for service, review this list. It may save you time and
expense. The list includes common occurrences that are not the result
of defective workmanship or materials in this appliance.
Avoid Service Checklist
OCCURRENCE
POSSIBLE CAUSE/SOLUTION
Surface burners do not light.
Surface control knob has not been completely turned to LITE. Push in and turn the
surface control knob to LITE (until burner ignites) and then turn the surface control
knob to the desired flame size.
Burnerportsare clogged. Clean burners. See "To Clean the BurnerGrates, Contoured
BurnerPans, BurnerCap Assembly, and BurnerBase" underGeneralCleaning. With
the burner off, use a small-gauge wire or needle to clean ports.
ElectricalPoweroutage (ElectricIgnition modelsonly). Checkhouse lightsto be sure.
Call your local electric company for service. Surface burners can be lit manually. See
Setting Surface Controls in this Owner's Guide.
Gas supply is turned off. Turn gas supply on.
Surface burner flame burns half w ay
around.
Burner ports are clogged. With the burner off, clean by using a small-gauge wire or
needle to clean ports.
Moisture is present after cleaning. Lightly fan the flame and allow the burner to
operate until flame is full. Dry the burners thoroughly following instructions under
GeneralCleaning.
Surface burner flame is orange.
Dust particlesin main line. Allow the burnerto operate a few minutesuntilflame turns
blue.
Salt air in coastal areas. A slightly orange flame is unavoidable.
9
Notes
10
Notes
11
WHITE-WESTINGHOUSE COOKTOP WARRANTY
Your White-Westinghouse product is protected by this warranty
WHITE-WESTINGHOUSE, THROUGHITSAUTHORIZED
SERVICERS, WILL:
THECONSUMERWILLBE
RESPONSIBLEFOR:
WARRANTY
PERIOD
FULLONE-YEAR
WARRANTY
Pay all costs for repairing or replacing any parts of this Costs of service calls that are listed under NORMAL
appliance which prove to be defective in materials or RESPONSIBILITIES OFTHECONSUMER.*
workmanship.
One year from original
purchase date.
LIMITED WARRANTY
(Ap p lica b le t o t h e
St a t e o f Ala ska )
All of the provisions of the full warranty above and the Costsof the technician'stravelto the home and any
Time period listed above.
exclusions listed below apply.
costs for pick up and delivery of the appliance
required because of service.
Your appliance is warranted by Frigidaire Company, a division of White Consolidated Industries, Inc. We authorize no person to change or add
to any of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by Frigidaire Company
Consumer Services or an authorized White-Westinghouse servicer.
* NORM AL
RESPONSIBILITIES
Th is w a rra n t y a p p lie s o n ly t o p ro d u ct s in o rd in a ry h o u se h o ld u se , a n d t h e co n su m e r is re sp o n sib le fo r t h e
it e m s list e d b e lo w :
OF THE CONSUMER 1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in
accordance with all local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which
are not a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
EXCLUSIONS
Th is w a rra n t y d o e s n o t co ve r t h e fo llo w in g :
1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING
FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation
or exclusion may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary
household use. The consumer shall pay for such service calls.
3. Damages caused by services performed by persons other than authorized White-Westinghouse servicers; use of parts
other than Frigidaire Company Genuine Renewal Parts; obtained from persons other than such servicers; or external
causes such as abuse, misuse, inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty
period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This
written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under
this warranty must be obtained by following these steps, in order:
IF YOU NEED
SERVICE
1. Contact Frigidaire Company Consumer Services or an authorized White -Westinghouse servicer.
2. If there is a question as to where to obtain service or parts, call or write our Consumer Relations Department at:
White-Westinghouse
P.O. Box 7181
Dublin, Ohio 43017
(800) 944-9044
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made
by White Consolidated Industries, Inc. This warranty applies only in the 50 states of the U.S.A. and Puerto Rico.
|